Wrought Iron Fence Repair in Heath, TX
Make the fence look as good as the yard.
A beautiful front yard deserves a fence to match
Heath properties are kept well. The landscaping is maintained, the stonework is clean, the drives are swept — and then there is a run of ornamental iron going orange at the base with the paint flaking off it. Nothing pulls down the front of a property faster.
The ironwork here is worth the effort. It tends to be heavier, longer and better made than average — estate perimeters, entrance gates, courtyard and pool enclosures, long runs fronting golf course and water. We are in Rockwall County, minutes away, and we bring that iron back rather than replacing it.
Estate ironwork rarely needs replacing. See how our wrought iron fence repair work restores a run so the repairs do not show.
Entrance gates on operators are unforgiving when a post shifts. That is leaning post and sagging gate work.
Heath sits right next to us. Most of our work is wrought iron fence repair in Rockwall County, and the same crew covers Heath.
What we see most in Heath
Higher-end ironwork, longer runs, and a standard of finish that has to be met.
Estate perimeters
Long ornamental runs fronting acreage, golf course and water. They fail in sections rather than all at once, and the repair has to blend across the whole length.
Entrance gates
Wide, heavy driveway gates, often tied into masonry columns and running on operators. Sagging, dragging and hinge wear are the usual faults.
Lake and golf frontage
Iron facing open water or fairway takes constant moisture, wind and sun with nothing breaking it. Finishes fail faster on these runs.
Courtyard and pool enclosures
Ornamental panels and self-closing gates close to the house, where the detail and finish are seen up close every day.
Missing or damaged custom sections
Where a panel, finial or decorative section is beyond saving, we fabricate a replacement to match the existing work rather than substituting something off a shelf.
Previous cosmetic repairs
Sections sprayed or touched up by someone else, now standing out from the rest of the run. Very visible on a property of this standard.
See the difference
The same fence before and after. Scraped back to sound metal, welded where needed, and hand-finished end to end so the repair does not show.
Restored, and made better where it needs it
Ornamental iron on an estate property is usually better made than what is sold today — heavier stock, custom panels, details built for that house. Replacing it means a fence that does not match the property, at a cost that reflects the length of the run rather than the size of the problem.
We do custom fabrication as well as repair, so we are not limited to what can be patched. Damaged or missing panels, finials and decorative sections can be made to match the existing ironwork. Add a gate, widen an opening, replace a section that is genuinely beyond saving — it gets built to suit the fence you already have, then the whole run is finished together so it reads as one.
- Custom fabrication in house, so damaged sections are matched rather than substituted.
- Whole runs finished end to end so repairs do not show.
- Based in Rockwall County, minutes from Heath.
- Our welds are guaranteed, with one free touch-up in the first year.
How we restore a wrought iron fence
Prep
The crew works the whole run first, scraping every bit of flaking and failing paint back to sound metal. On a long estate perimeter this is most of the job, and it is what decides whether the finish holds.
Metal work
Rusted-through sections are cut out and new metal welded in to match. Separated welds are rewelded and leaning posts pulled and reset.
Gates
Every gate works properly when we leave — realigned, rehung, rewelded, latch rebuilt. Where an operator is involved we will tell you whether the fault is the gate or the opener.
Paint
Hand-brushed oil-based Rust-Oleum with a rust inhibitor, applied across the whole run rather than just the repairs, so there is no visible patch.
Walkthrough
Before the crew leaves, they walk the fence with you. Anything not right gets put right while they are still on site.
Get a free estimate in Heath
Send a few photos of the run or have us out to walk it. Whether it needs restoring, a section fabricating, or both, we will tell you straight.
Iron fence restoration in Heath — common questions
Do you work on estate properties in Heath?
Regularly. Long ornamental perimeters, entrance gates, courtyard and pool enclosures are all routine work for us, and we are based in Rockwall County so Heath is minutes away.
Will the repaired section be visible?
Not if it is done properly. We finish the whole run rather than just the repair, hand-painting end to end so there is no patch to see. On a property at this level that is the point of the job.
My fence faces the lake and the rust is worse there. Why?
Iron facing open water takes constant moisture and wind with nothing breaking it, and the sun does the rest. Runs on lake and golf frontage almost always fail before the rest of the property.
Heath requires iron fencing on lakefront lots. Does that affect repairs?
City code calls for ornamental iron or tubular steel with open area on lakefront property to protect the views, which is part of why there is so much iron here. Repairing the existing run keeps you within what is already approved.
Can you repair a heavy entrance gate on an operator?
Yes. We repair the gate itself — frame, posts, hinges and finish. If an operator is involved we will tell you whether the fault is the gate or the opener, because a dragging gate will burn out an operator.
Someone touched up my fence before and it looks wrong. Can that be fixed?
Yes. Previous cosmetic repairs and sprayed sections get taken back and brought in line with the rest of the run.
Can you fabricate a replacement for a damaged custom panel?
Yes. We do custom fabrication as well as repair, so where a panel, finial or decorative section is genuinely beyond saving we make one to match the existing ironwork rather than substituting something off the shelf. It is welded into the run and finished with the rest so it does not stand out.
How much does it cost?
A fraction of replacement. It depends on the length of the run, how much metal has to be cut out and how many posts and gates are involved. Estimates are free.